Custom Stainless Steel Stacker Based on Sinolift CTD1000SR
A practical case about adapting a stainless steel semi-electric clamp roll lifter platform for a non-standard shipment configuration.
This shipment is best understood as a custom stainless steel handling unit built on the CTD1000SR standard platform. The base product explains the verified roll-handling functions; the supplied photographs document the finished stainless build. The final custom capacity and dimensions must remain tied to the approved project drawing.
The Handling Requirement
When a standard stacker needs a hygienic, load-specific interface
Round materials can roll, finished surfaces can be damaged and painted carbon-steel equipment may be a poor fit for wet, clean or corrosion-sensitive areas. The handling task is therefore defined by the load and the environment, not only by lifting height.
The supplied project folder contains shipment images for a non-standard stainless steel stacker. The user-provided product link identifies the base as Sinolift CTD1000SR, a stainless steel semi-electric clamp roll lifter. Official product information describes a 304 stainless body, electric hydraulic lifting, a reinforced hydraulic cylinder, a round clamp, 360-degree rotation and transport, stacking and rotating functions.
304 stainless foundation
The standard platform is intended for wet, clean or corrosion-sensitive work areas, subject to the final cleaning specification.
Round-load handling
A clamp-based interface is designed around cylindrical materials rather than pallet-only loads.
Orientation control
The standard platform is described with 360-degree rotation for positioning and orientation tasks.
Project-specific build
The shipment photos document a custom stainless unit; actual final dimensions require drawing confirmation.
Shipment Evidence
What the supplied photographs show
The images show a narrow stainless steel machine with a vertical mast, long front load-supporting members, stainless body panels, operator-facing protection and caster wheels. One image shows the unit during production or assembly, while the others show the completed machine outdoors. These photographs establish the visible build and shipment context, not the final load rating or customer result.
Standard Product Foundation
CTD1000SR facts versus custom shipment facts
The table below keeps the standard product information separate from the non-standard shipment evidence. Published standard values are not proof of the exact delivered configuration.
| Parameter | Published standard value | Evidence status for shipment |
|---|---|---|
| Body material | 304 stainless steel | Stainless body visible in photos |
| Standard capacity | 500 kg | Confirm final custom value |
| Drum diameter range | 400-1,000 mm | Confirm actual application range |
| Maximum lifting height | 1,300 mm | Confirm final custom height |
| Clamp opening | 380-1,100 mm | Confirm final attachment geometry |
| Rotation | 360 degrees | Confirm final rotation function |
| Battery | 12 V / 93 Ah | Confirm shipped configuration |
Buyer Evaluation
Questions that define the custom version
-
1
What is the load?
Record maximum weight, outer diameter, width, core or contact geometry, center of gravity and surface sensitivity.
-
2
What movement is required?
Define transport, machine-side positioning, stacking, rotation, release height and the required operating sequence.
-
3
What is the route?
Measure doors, aisles, turning points, floor transitions and production-machine clearances, including the attachment and load.
-
4
What does cleaning require?
Specify washdown method, humidity, chemicals, protected components and any hygiene or compliance requirements.
-
5
What must acceptance prove?
Verify engagement, lifting, lowering, stopping, movement, rotation, surface protection, controls and maintenance access.
Application Fit
Where to evaluate this type of stainless handling solution
Wet or clean processing
Evaluate stainless construction where moisture, cleaning and corrosion resistance influence equipment selection.
Controlled material flow
Review surface, access and compliance requirements for pharmaceutical production or storage areas.
Cylindrical materials
Consider for round loads such as rolls, reels or drums after confirming diameter, weight and clamp contact.
FAQ
Frequently asked questions
What is the CTD1000SR?
The CTD1000SR is Sinolift's stainless steel semi-electric clamp roll lifter for round materials, with a clamp and rotation-oriented handling platform.
What standard capacity is published?
Sinolift's official product information lists a standard maximum capacity of 500 kg. The capacity of this non-standard shipment must be confirmed against the project quotation and drawing.
Why use stainless steel for a stacker?
Stainless steel is considered for wet, clean, corrosion-sensitive or hygiene-focused work areas. The complete cleaning and compliance specification must be verified.
What information is needed for a custom version?
Provide load weight, diameter, width, center of gravity, required lift height, rotation needs, route dimensions, cleaning conditions, duty cycle and machine interface.